Cost per square foot by foam type
| Foam type | Typical installed cost per sq ft | Commonly used for |
|---|---|---|
| Open-cell | $1.50 – $3.50 | Interior walls, attics in moderate climates, sound control |
| Closed-cell | $3.00 – $5.00 | Exterior walls, basements, crawl spaces, damp areas |
Source: HomeGuide national averages (December 2025). These figures are per square foot of surface that gets sprayed, not the floor area of your home.
Closed-cell costs more per inch, but it also insulates more per inch, so you need less thickness to reach the same R-value. Our open-cell vs closed-cell guide explains which one fits which part of the house.
Typical cost by area of the home
| Area | Typical total cost |
|---|---|
| Rim joists | $2,000 – $2,500 |
| Crawl space | $2,000 – $4,000 |
| Attic | $3,000 – $8,000 |
| Basement | $2,500 – $9,000 |
| All exterior walls | $4,000 – $10,000 |
| Whole house | $8,000 – $20,000 |
Source: HomeGuide (December 2025). Your house can land outside these ranges.
What drives the price
- Foam type. Closed-cell costs more per square foot than open-cell.
- Thickness. Spray foam is priced by the board foot: one square foot sprayed one inch thick. Doubling the thickness roughly doubles the foam. Check the spray foam thickness chart to see how many inches it takes to hit a given R-value.
- Job size. Bigger jobs usually get a better rate per square foot. Small jobs often hit the contractor’s minimum charge.
- Access. An open attic or unfinished basement is quicker to spray than a tight crawl space or finished walls.
- New build or existing home. Open stud walls in new construction are the easiest. In an existing home, the crew may have to open walls or use injection foam instead.
- Removing old insulation. HomeGuide puts removal at about $1.00 to $2.50 per square foot, if the old material has to come out.
- Where you live. Labor rates vary a lot from one market to the next.
How to compare quotes
Two quotes at the same price per square foot can be very different jobs. Ask every contractor to put these in writing:
- Which areas will be sprayed, and the square footage of each
- Open-cell or closed-cell, and the brand of foam
- The finished thickness in inches and the R-value it reaches
- Whether removing old insulation, prep, and cleanup are included
- Whether an ignition or thermal barrier is needed and who provides it
- How long you’ll need to stay out of the house while the foam cures
- The warranty, and what it covers
If a quote won’t say the thickness, ask why. A thinner job always looks cheaper on paper. Our guide on why spray foam installations fail covers what else to watch for, and how to choose a spray foam contractor lists the questions to ask before you sign. For a rough estimate for your own home, try our spray foam savings calculator.
Is it worth paying more than for other insulation?
Spray foam costs more up front than fiberglass batts or blown-in insulation. What you get for that is air sealing and insulation in one step, plus more R-value per inch (HomeGuide lists about 3.5 to 7 per inch for spray foam, versus 2.2 to 2.9 for fiberglass batts). That’s why it’s often used on rim joists, attics with ductwork, and crawl space walls. Whether it pays off depends on your climate, your energy bills, and what you’re insulating, so ask your contractor to explain why foam is the right choice for that area of your house.
FAQ
How much does spray foam insulation cost per square foot?
About $1.50 to $5.00 per square foot installed, according to HomeGuide’s national averages. Open-cell is usually $1.50 to $3.50 and closed-cell $3.00 to $5.00.
What is a board foot of spray foam?
One square foot of foam sprayed one inch thick. Contractors price foam this way, so thickness changes the price as much as the area does.
Why is there a minimum charge?
Every job takes the same setup: the spray rig, masking, safety gear, and travel. That’s why many contractors set a minimum of $1,000 to $2,000 or more.
Is closed-cell worth the extra cost?
It depends on the spot. Closed-cell is usually picked for crawl spaces, basements, and exterior walls where moisture is a concern. Open-cell is common in attics and interior walls. See our moisture guide.