Two ways to insulate a crawl space
Sealed (unvented) crawl space. The vents are closed, a ground vapor barrier goes down, and the insulation goes on the foundation walls and the rim joists. The crawl space becomes part of the insulated house. The U.S. Department of Energy’s Building America program says this gives ducts and equipment a mild space to run in, so they last longer and work more efficiently. It also helps keep out humid outside air and moisture coming up from the ground.
Vented crawl space. The vents stay open to the outside, and the insulation goes between the floor joists, on the underside of the floor above. The crawl space stays outside the insulated house.
| Sealed (insulate walls) | Vented (insulate floor) | |
|---|---|---|
| Ducts, furnace and pipes | Inside the insulated space | Left in outdoor heat, cold and humidity |
| Humid climates | Recommended by DOE Building America | Prone to condensation on cool ducts and joists |
| Ground moisture | Controlled by a sealed vapor barrier | Depends on vents and a ground cover |
| Area to insulate | Foundation walls and rim joists | The whole floor area |
| Local code | Must meet the unvented-crawl-space rules | Simpler in most areas |
Which one fits your house?
- Humid climates (much of the Southeast and Gulf Coast): DOE’s Building America researchers recommend converting the crawl space to unvented and insulating its walls. Summer air coming in through open vents can condense on cool ducts and floor framing.
- Dry or marine climates: DOE’s insulation guide for homeowners says underfloor insulation is an option here.
- Ducts or HVAC in the crawl space: sealing the crawl space brings them inside the insulated part of the house, the same reason a roof-deck attic makes sense when the ducts are in the attic.
Why spray foam is used on crawl space walls
Building America’s checklist for converting a vented crawl space to an unvented one calls for the foundation walls to be insulated with spray foam or rigid foam. Closed-cell spray foam is a common pick because it bonds directly to block or poured walls, fills gaps around pipes and wires, and seals the rim joist in the same pass. Rigid foam board is the other common option.
How much insulation do crawl space walls need?
ENERGY STAR’s retrofit recommendations for basement and crawl space walls, which are based on the 2021 International Energy Conservation Code, are:
| Climate zone | Crawl space wall insulation |
|---|---|
| Zone 3 | R-5 insulative wall sheathing or R-13 batt |
| Zones 4A and 4B | R-10 insulative wall sheathing or R-13 batt |
| Zones 4C and 5 through 8 | R-15 insulative wall sheathing or R-19 batt |
Your local code may require more, so ask your contractor what R-value your area requires and get it written on the quote.
What a good crawl space job includes
DOE’s Building America guidance for sealed crawl spaces lists these details. They’re worth asking about on any quote:
- A ground vapor barrier. Building America calls for at least 6-mil polyethylene that covers the whole floor and runs up the walls, with seams overlapped (it recommends 12 inches) and sealed.
- All vents closed and sealed, including any gaps around pipes and wires.
- Rim joists insulated and sealed.
- A termite inspection gap where local code requires one. In areas prone to termites or carpenter ants, Building America describes a 3-inch strip of bare wall left at the top of the foundation.
- Fire protection. Building America notes that foam in a crawl space has to meet the ignition barrier requirements for that space, and the foam has to meet your local fire code.
- A plan for radon and air. Building America recommends a radon vent under the vapor barrier. Ask your contractor how the air in the sealed crawl space will be kept dry, and which option your local code allows.
- Access doors insulated and weatherstripped.
Questions to ask before you hire
- Will the crawl space be sealed or vented, and why is that right for my climate?
- What R-value will the walls reach, and is it written on the quote?
- Is the foam you’re using rated for exposed use in a crawl space, or will it need a covering?
- How will the air in the crawl space be dried or conditioned once the vents are closed?
- Will you leave a termite inspection gap, and does my area require one?
- Will you pull a permit, if one is required?
For a rough cost and payback estimate for your home, try our spray foam savings calculator.
FAQ
Is spray foam good for crawl spaces?
Yes, especially on the foundation walls and rim joists of a sealed crawl space. It insulates and air-seals in one step. The DOE’s Building America checklist for sealed crawl spaces calls for spray foam or rigid foam on the walls.
Should I spray foam under my floor or on my crawl space walls?
In most humid climates, and whenever ducts or a furnace are down there, the walls. Underfloor insulation is mainly an option for vented crawl spaces in dry or marine climates.
Do I need a vapor barrier if I spray foam my crawl space?
Yes. A sealed crawl space needs a ground vapor barrier. DOE’s Building America calls for at least 6-mil polyethylene over the whole floor, run up the walls and sealed at the seams.
Can I close my crawl space vents after insulating?
Closing the vents is part of sealing a crawl space, but it has to be done with the full package: a vapor barrier, insulated walls, and a plan for keeping the air dry that meets your local code. Don’t just block the vents on their own.